Shop for splash proof atc fuse block terminal

Heavy-duty. Black plastic molded base with ground bar. 30 Amp at 12-Volt DC. Material: Metal.

Heavy-duty molded base. Brass clips and contacts with common buss bar. Use SFE 20A or 3AG series fuse. Each buss bar has 1 # 8 in. to 32 in. x 3/4 in. stud with 2 hex nuts. Material: Metal.

Heavy-duty. Black plastic molded base with ground bar. 30 Amp at 12-Volt DC. Material: Metal.

Heavy-duty molded base. Brass clips and contacts with common buss bar. Use SFE 20A or 3AG series fuse. Each buss bar has 1 #8-32 x 3/4 in. stud with 2 hex nuts. Material: Metal.

Bussmann Division BP/ATC-40-RP ATC Fuse - 40 Amp, Blister Pack. Blister pack of 5. Quick and easy installation. Refer to manufacturer recommendations to ensure a proper fit.

Compact ATO /ATC fuse block consolidates branch circuits and eliminates the tangle of in-line fuses. Includes a clear insulating cover with label recesses. Uses Blue Sea small format labels and offers storage for one fuse, satisfies ABYC/USCG insulation requirements. Independent circuits allow some 24-hour and some switched circuits in the same block. Tin-plated copper buses and fuse clips. 32 Volts maximum. Product quality is managed in a manner consistent with international standards. Quality products engineered for the harsh marine environment.

2 isolated 6-circuit fuse blocks with a negative bus. For use when a mix of switched and 24-hour circuits are desired in the same block. Common and/or independent source fuse block. Provides 2 isolated groups of 6 ATO/ATC circuits. For use with either 2 isolated batteries or with a single battery providing a mix of 24-hour and switched circuits. Clear insulating cover satisfies ABYC/USCG insulation requirements and provides storage for 2 spare fuses. Accepts ring terminals. Easy to open, push button latch provides easy access to fuses. Tin-plated copper buses and fuse clips. Includes 20 write-on circuit labels. Fuses sold separately. Specifications Voltage Maximum Operating: 32-Volt DC. Amperage Maximum. Operating: 30 Amp per circuit 100 Amp total (not to exceed 80 Amp per load group). Fuse Type: ATO or ATC Fuses. Screw Terminal: #8-32 Screws with captive star lock washer. Mounting: #8 Screw (M4). Recommended Wire Size: Positive Feed: 4 AWG to 6 AWG (25 mm to 16 mm), Branck Circuits: 10 AWG to 16 AWG (6 mm to 15 mm). Recommended Torque: #10 Stud: 24 in./lbs. (2.71 Nm), #8 Screw: 18 in./lbs. (2.03 N-m). Material: Plastic.

Easy to install 4 ATO /ATC fused circuits mounts directly on the battery terminal studs. Screw terminals for securing wires with ring terminals and insulating covers included. Screw terminals for securing wires. Accepts small format circuit labels. Insulating cover meets ABYC/USCG insulation requirements. Ignition Protected - for use in a gasoline engine compartment. Includes 4 write-on circuit labels. Includes four 16-14 AWG and four 12-10 AWG Nylon insulated ring terminals. Fuses sold separately. Product quality is managed in a manner consistent with international standards. Quality products engineered for the harsh marine environment.

A convenient means of adding fused circuits to power accessories or auxiliary loads. Each pole has its own 1/4 in. male quick-connect isolated terminals (power is not provided by a common bus). These blocks feature a back plate for additional safety and electrical isolation. The clear cover has an O-ring seal to help keep out contaminants and makes it easy to inspect fuses (fuses not included). 15A per circuit. Operating environment: minus 40°C to 105°C (minus 40°F to 221°F), 95% RH non-condensing. Uses two 5.5mm mounting holes for M5 (#10) screws. Wire range per circuit: #12 16g (Wire size dependent on length of run)#16 ga. up to 10 ft. #14 ga. up to 20 ft. #12 ga. up to 25 ft. Material: Metal.

A convenient means of adding fused circuits to power accessories or auxiliary loads. Each pole has its own 1/4 in. male quick-connect isolated terminals (power is not provided by a common bus). These blocks feature a back plate for additional safety and electrical isolation. The clear cover has an O-ring seal to help keep out contaminants and makes it easy to inspect fuses (fuses not included). 15A per circuit. Operating environment: minus 40°C to 105°C (minus40°F to 221°F), 95% RH non-condensing. Uses two 5.5 mm mounting holes for M5 (#10) screws. Wire range per circuit: #12 16 g (Wire size dependent on length of run)#16 ga. up to 10 ft. #14 ga. up to 20 ft. #12 ga. up to 25 ft. Material: Metal.