Shop for 3 flute downcut spiral end mill

Best for achieving smooth finish on hard plastics. Cutting Diameter: 1/2 in. Cutting Height: 1-1/4 in. Shank Diameter: 1/2 in. Overall Length: 3 in. Flutes: 2 Low Helix bits perform a more lateral movement with less upward or downward motion resulting in a smoother finish on single layer materials. These bits are a better choice for hard plastics such as acrylic and phenolic. Down cut endmills shear in a downward direction causing the uppermost layer of the material to be pressed down against the material just below it. This motion leaves a perfectly clean top surface edge. A concentration of wood chips in the work path will occur. Hose away excess wood chips to prevent bit breakage. To get a smooth finish in hard plastics like acrylic with your CNC router, use a low helix spiral end mill. The modified cutter angle produces a better finish in plastics than standard spiral bits. Down cut bits pull chips downward, producing a clean top edge in your parts. Consequently, the chips accumulate in the cut path and should be removed to prevent bit breakage. Low helix bits require slower feed speeds than normal high helix bits.

Best used for: Standard milling, dadoing and boring. Cutting Diameter: 1/8 in. Cutting Height: 1/2 in. Shank Diameter: 1/4 in. Overall Length: 2 in. Flutes: 3 Up-cut endmills direct woodchips up and away from the milling area leaving an unobstructed path for the endmill. Bit breakage is less likely. Up cut end mills are the best choice for most standard milling applications. The up cut direction can leave behind a minimally rough top surface edge. Up cut endmills are great for all standard milling and material removal. These bits pull the wood chips up and away from the tool path which helps prevent tool breakage and extends the life of the bit. If a particular finish is required for your project, use a down cut or compression cut end mill for the final pass.

Best used for: Standard milling, dadoing and boring. Cutting Diameter: 1/8 in. Cutting Height: 1/2 in. Shank Diameter: 1/4 in. Overall Length: 2 in. Flutes: 2 Up-cut end mills direct woodchips up and away from the milling area leaving an unobstructed path for the end mill. Bit breakage is less likely. Up cut end mills are the best choice for most standard milling applications. The up cut direction can leave behind a minimally rough top surface edge. Up cut end mills are great for all standard milling and material removal. These bits pull the wood chips up and away from the tool path which helps prevent tool breakage and extends the life of the bit. If a particular finish is required for your project, use a down cut or compression cut end mill for the final pass.

This 2 flute round nose endmill has a cutting diameter of 3/8 in. and a cutting length of 1-1/16 in. The shank is 1/2 in. Dia and the overall length is 3 in. Ball nose spiral end mills are used for smooth contouring and fine detail passes with a CNC router and often for complex shapes like 3D carvings. The rounded tips reduce tool markings, which produce smooth curves that would be impossible to achieve with flat end bits. Small diameter ball nose end mills are used for projects with intricate detail while larger bits are used for smoother projects with more gradual slopes. These bits are also excellent for routing fluted columns and channels in cutting boards and countertops edges.

This 2 flute round nose endmill has a cutting diameter of 3/8 in. and a cutting length of 1-1/4 in. The shank is 3/8 in. Dia and the overall length is 3 in. Ball nose spiral end mills are used for smooth contouring and fine detail passes with a CNC router and often for complex shapes like 3D carvings. The rounded tips reduce tool markings, which produce smooth curves that would be impossible to achieve with flat end bits. Small diameter ball nose end mills are used for projects with intricate detail while larger bits are used for smoother projects with more gradual slopes. These bits are also excellent for routing fluted columns and channels in cutting boards and countertops edges.

This 3 flute solid carbide down cut rougher end mill has a 3/8 in. cutting diameter with a cutting length of 1-3/8 in. The shank diameter is 3/8 in. and the overall length is 3-1/2 in. Rougher end mills remove lots of material with every pass. The Rougher feature limits the size of the chips preventing the bit from getting bogged down. These end mills are not meant to be used on the finishing pass of the project.

Best for achieving smooth finish on hard plastics. Cutting Diameter: 3/16 in. Cutting Height: 3/4 in. Shank Diameter: 1/4 in. Overall Length: 2 in. Flutes: 3 Low Helix bits perform a more lateral movement with less upward or downward motion resulting in a sm To get a smooth finish in hard plastics like acrylic with your CNC router, use a low helix spiral end mill. The modified cutter angle produces a better finish in plastics than standard spiral bits. Downcut bits pull chips downward, producing a clean top edge in your parts. Consequently, the chips accumulate in the cut path and should be removed to prevent bit breakage. Low helix bits require slower feed speeds than normal in.high helix in. bits.

Best for achieving a smooth finish on laminate or veneer finish applications. Cutting Diameter: 1/4 in. Cutting Height: 1 in. Shank Diameter: 1/4 in. Overall Length: 2-1/2 in. Flutes: 3 Compression bits cut down from the top of the stock and up from the bottom of the stock simultaneously. The bit's unique and complex geometry forces the trimmed material to be compressed toward the center of the stock leaving behind a smooth and sharp finish free of chips on both the top and bottom edges. This bit can also be used for mortising projects that require a smooth bottom surface without sacrificing the mortised edge finish. When working with any veneer finished material in your CNC machine, you need a compression spiral end mill to make full depth cut. These bits are designed to leave clean edges on the top and bottom faces of any material. The compression bit's unique design pulls chips upward at the bottom of the stock and downward at the top face, producing chip-free surfaces that are perfect for cabinet and furniture parts. Compression cut spiral end mills are excellent for melamine, plywood, MDF and solid wood.

Best used for: Laminate or veneer-finish plunging and dadoing. Cutting Diameter: 1/4 in. Cutting Height: 3/4 in. Shank Diameter: 1/4 in. Overall Length: 2-1/2 in. Flutes: 3 Down cut endmills shear in a downward direction causing the uppermost layer of the material to be pressed down against the material just below it. This motion leaves a perfectly clean top surface edge. A concentration of wood chips in the work path will occur. Hose away excess wood chips to prevent bit breakage. Down cut CNC end mills are great for dado, pocket and inlay work as well as the final pass on most projects. These bits are especially useful when routing material such as melamine and plywood. Down cut spiral bits are designed to produce perfectly clean edges on the top face of the work piece but since the bits geometry causes the wood chips to travel in a downward direction, which will cause the tool path to be obstructed, it should only be used in applications where the desired finish is required.

2 flute end mill. Single End Style. Carbide End Mill. Square Shape.

EANOSIC Downcut Spiral Router Bit 3-Flute with 1/2” Shank, 1/2” Cutting Diameter, 1-1/4” Cutting Length, Carbide CNC Router Bits End Mill for Wood Mortises Carving Engraving(3 Inch OVL)

YONICO Downcut Router Bits Spiral 3 Flute Solid Carbide CNC End Mill 1/4-Inch Dia. 1/4-Inch Shank 32311-SC

YONICO Downcut Router Bits Spiral 3 Flute Solid Carbide CNC End Mill 1/8-Inch Dia. 1/4-Inch Shank 32310-SC

YONICO Downcut Router Bits Spiral 3 Flute Solid Carbide CNC End Mill 3/16-Inch Dia. 1/4-Inch Shank 32313-SC

YONICO Downcut Router Bits Spiral 3 Flute Solid Carbide CNC End Mill 5/32-Inch Dia. 1/4-Inch Shank 32312-SC

YONICO Downcut Router Bits Spiral 3 Flute Solid Carbide CNC End Mill 7/32-Inch Dia. 1/4-Inch Shank 32314-SC

YONICO Downcut Router Bits Spiral 3 Flute Solid Carbide CNC Low Helix End Mill 1/2-Inch Diameter 1/2-Inch Shank 36361-SC

YONICO Downcut Router Bits Spiral 3 Flute Solid Carbide CNC Low Helix End Mill 1/8-Inch Dia. 1/4-Inch Shank 36310-SC

YONICO Downcut Router Bits Spiral 3 Flute Solid Carbide CNC Rougher End Mill 3/8-Inch Dia. 3/8-Inch Shank 36269-SC

YONICO Upcut Router Bits Spiral 3 Flute Solid Carbide CNC Rougher End Mill 1/4-Inch 1/4-Inch Shank 36366-SC