Shop for 1800 pop up sprinkler head 6 emitter drip irrigatio

DIG's 1 GPH Button Barbed Dripper that comes in packs of 10 is easy to open and take apart for cleaning. The dripper features labyrinth water flow paths that allow for a consistent flow rate at an incoming pressure of 15 to 25 psi with higher discharge at higher pressures and lower discharge at lower pressures. Chemical and clog resistant, the drippers are an economical choice for all type of drip irrigation installations and recommended for residential, commercial and agricultural applications. These drip emitters are a low-cost solution for an individual plant, planter boxes, rows planting, vegetable rows, small to large pots, groundcovers, shrubs and trees, low-pressure gravity feed drip irrigation installations and areas where conventional sprinkler systems are not practical. The button drip emitter is made of two-piece construction and can be taken apart for cleaning by twisting the top part of the drip emitter counterclockwise and pulling it apart. Color: Blacks.

The Multi-Stream Drip Emitter is an ideal sprinkler for watering annuals in a flowerbed or container. The full pattern, gentle multi-stream extends up to 3 ft. at typical drip operating pressure of 30 PSI. You can decrease the spray radius, or even shut it all the way off, by rotating the multi-stream head clockwise. The 10-32 male thread (MT) inlet on the multi-stream emitter connects to an optional 6- or 12-in. drip stake with 10-32 female thread (FT). The inlet also has a barb for direct connection to 1/4-in. tubing and you can then hold the emitter in place at each plant with a drip tubing Y-anchor stake. You can either run 1/4-in. drip tubing from a drip manifold, a 1/2-in. drip tubing "lateral" line, or directly off the hose faucet with a 1/4-in. hose faucet x 1/4-in. adapter. Recommended operating pressure is 30 PSI. For outdoor irrigation use with cold water only. Color: Blacks.

This 1/2 in. Pipe Thread Adapter can help adapt your sprinkler risers into water-efficient low-volume irrigation systems. Connect the male pipe thread with semi-rigid riser into the FNPT and thread or insert the micro sprinkler, micro sprayer or drip emitter into the top of the PE riser. Accommodates most all threaded emitters. Color: Blacks. Material: ABS Plastic.

The Rain Bird Pop-Up Sprinkler to Drip Emitter Conversion Kit turns your sprinkler head into a 6-port drip emitter watering system. Ideal for larger planting beds and gardens. By applying water directly to the root zone of your plants, you eliminate wasteful overspray and improve plant health while using less water. Color: Blacks.

K-It Drip Regulator 25 psi Pressure Regulator, designed to regulate the pressure of your drip irrigation or micro sprinklers, or anything low volume, 3/4 in. Female Hose Thread x 3/4 in. Male Hose Thread. This Drip irrigation pressure regulator connects quickly and easily to any 3/4 in. threaded outdoor faucet, garden hose or component. K-It Drip Irrigation 25 psi Pressure Regulator reduce and regulate the incoming pressure of the household's water entering a drip irrigation or micro sprinkler system to the appropriate operating pressure of 25 psi. The pressure regulators, installed into the faucet after (downstream of) the backflow device or filter, offer reliable pressure control and provide consistent outlet pressures over a wide range of incoming pressures up to 100 psi. The K-It Drip Regulator offers exceptional pressure control and provides consistent outlet pressures over a wide range of incoming pressures. Designed and engineered by Glenn Grizzle, Industry Pioneer with 50 plus years of irrigation innovations. The GV Series Preset Pressure Regulator is an irrigation work-horse ideal for drip line, soaker hose and other residential and commercial (landscape grade) low volume irrigation. Properly regulates water pressure and flow to a Drip irrigation system, maintaining optimum 25 psi pressure and water flow to Drip lines and emitter devices. Simply screw into place so rubber gasket seals to assure leak-proof performance. Color: Blacks.

The drip irrigation emitter with nozzle twist design can meet various water output needs and control the water output while controlling the effect of water. The irrigation dripper interface can be firmly fixed to various outlet pumps, and will not fall off easily even when affected by water pressure. ABS material allows the adjustable tap emitter to have rust resistant properties. No impurities in the rain and no pollution of the water. The sprinkler drip head can be used for watering plants and cooling humidifier greenhouses, balconies, etc. The range of use is free.

DIG's 4 Outlet PC Drip Emitter is a drip irrigation manifold with built-in anti-drain valve. This unique design ensures even distribution uniformity of flow for each outlet and eliminates drainage after the system valve is close. The manifold converts a 1/2. sprinkler riser into a 4-outlet drip irrigation system without altering the flow of the sprinkler system zone. The 4 Outlet PC Drip Emitter with built-in anti-drain valve connect to ¼ in. micro tubing or ¼ in. dripline to efficiently irrigate a wide variety of plants and trees. Color: Blacks. Material: Acrylonitrile Butadiene Styrene (ABS).

The Multi-Stream Drip Emitter is an ideal sprinkler for watering annuals in a flowerbed or container. The full pattern, gentle multi-stream extends up to 3 ft. at typical drip operating pressure of 30 PSI. You can decrease the spray radius, or even shut it all the way off, by rotating the multi-stream head clockwise. The 10-32 male thread (MT) inlet on the multi-stream emitter connects to an optional 6- or 12-in. drip stake with 10-32 female thread (FT). The inlet also has a barb for direct connection to 1/4-in. tubing and you can then hold the emitter in place at each plant with a drip tubing Y-anchor stake. You can either run 1/4-in. drip tubing from a drip manifold, a 1/2-in. drip tubing "lateral" line, or directly off the hose faucet with a 1/4-in. hose faucet x 1/4-in. adapter. Recommended operating pressure is 30 PSI. For outdoor irrigation use cold water only. Color: Blacks.

Rain Bird RCKIT-1PS Drip Irrigation Conversion Kit. Convenient kit converts underground sprinklers and 1/2" risers to water-saving Drip irrigation. All-in-one unit provides 30 PSI pressure regulation and 200-mesh filter screen for optimal Drip system performance. Saving up to 80% over sprinkler watering, Drip systems apply water directly to the root zone for healthier plants. In most instances, owners of Rain Bird 1800 Series pop-up sprinklers will make the conversion without digging. Kit will replace all pop-up sprinklers with a 1/2" threaded bottom inlet. If you have another brand dig out and remove old sprinkler and thread kit to existing 1/2" male fitting. Easy Fit Tee tubing connector allows for assembly to any 1/2" or 5/8" Drip tubing. Constructed of highly durable UV and chemical-resistant materials to assure long life. Requires capping other heads on the zone. Inlet pressure 15 to 70 PSI. Color: Blacks.

Rain Bird 1800CAPS Spray Head Cap for 1800 Series Sprinklers. Use this threaded cap to quickly and easily cap off pop-up spray heads when converting to Drip irrigation. No digging required to cap a Rain Bird 1800 series sprinkler; simply twist off existing cap, remove the internal mechanism and screw on the new cap. Gasketed cap provides a leak-tight seal of any unused heads on the zone. Cap designed to fit the world's #1 selling sprinkler head: the Rain Bird 1800 Series. Rain Bird "The Intelligent Use of Water".